# This file contains configuration for the OCSS7 SGC.
deployment-config:sgc:
  sgcenv:
    # The port to bind to for JMX service, used by the CLI and MXBeans.
    jmx-port: 10111

  hazelcast:
    # If omitted, backup-count defaults to N-1, where N is number of SMO nodes.
    # Don't uncomment, unless support instructs you to.
    # backup-count: 1

    password: xxxxxxxx

  # Only change SGC properties if support instructs you to
  #sgc-properties:
  #  properties:
  #    - name: com.cts.ss7.shutdown.gracefulWait
  #      value: '30000'

  m3ua:
    # The default port to bind for this local M3UA endpoint.
    local-port: 2905
#    # Normally each node in an SGC cluster will use the same port for its local M3UA endpoint.
#    # However, some configurations require that each node uses a different local port.
#    # Uncomment and configure if required.  For 'node-index', '1' is the first SMO node, '2' the
#    # second and so on.  Any nodes not configured here will use the global default 'local-port'
#    # above.
#    per-node-local-port:
#      - node-index: 2
#        local-port: 2906
#      - node-index: 3
#        local-port: 2907

    # The SCCP variant to configure this SGC to use.
    # Can be either: ITU or ANSI
    sccp-variant: ITU
    # This cluster's signaling point code.
    # If specifying a single integer (for ITU point codes), be sure to quote it
    # along with all other point codes in this file.
    point-code: "5"

    remote:
      peers:
        - id: 'STP-1'
          remote-ips:
            # The index of the SMO node that hosts the SGC that will be
            # connected to this IP set.  '1' is the first SMO node,
            # '2' is the second, and so on.  '-1' indicates that all
            # SGC nodes in the cluster will use this remote IP set.
            - node-index: -1
              ips:
                - 10.14.144.71
                - 10.14.144.134
          # The remote port for this M3UA association.
          port: 2906
          # The AS to which this connection belongs.
          application-servers:
            - as-id: 'NN-AS'

        - id: 'STP-2'
          remote-ips:
            - node-index: -1
              ips:
                - 10.14.144.81
                - 10.14.144.144
          port: 2906
          application-servers:
            - as-id: 'NN-AS'

      application-servers:
        - id: 'NN-AS'
          routes:
            default-priority: 5
            # The DPC identifiers applicable to this route.
            dpc-ids:
              - id: 'alias-2-233-3'
        - id: 'NN-AS2'
          routes:
            default-priority: 0
            # The DPC identifiers applicable to this route.
            dpc-ids:
              - id: 'alias-2-233-3'
          precond-ssns:
            - 2
            - 3
      dpcs:
        - id: 'alias-2-233-3'
          dpc: "5963"
          # maximum unsegmented SCCP message size to send to this
          # destination as a single unsegmented message
          muss: 252
          # maximum user data length per segment to send to this
          # destination
          mss: 245

      cpcs:
        - dpc: "5963"
          # The local SSNs to monitor.
          ssns:
            - 8
            - 146

    global-title:
      # For this example:
      # Match everything and send to the single alias point code.
      outbound:
        matchers:
          defaults:
            natofaddr: 0
            numplan: 7
            trtype: 129
          rules:
            - id: '1'
              is-prefix: false
              translations:
                - 'all'
        translations:
          - id: 'all'
            dpc: "5963"
            priority: 5

#        # Example rewriter would take all translation rules that
#        # use the 'example' rewriter, replace the digits with
#        # '123456', and set translated messages to route on the SSN.
#        rewriters:
#          - id: 'example'
#            addrinfo: '123456'
#            route-on: 'SSN'

      # Inbound translation has only matching rules.
      # If an address is matched, it is sent to the
      # configured SSN
      inbound:
        - id: 'to-sentinel-volte-gsm'
          addrinfo: '123456'
          is-prefix: false
          natofaddr: 4
          numplan: 1
          trtype: 0
          ssn: 146
        - id: 'to-sentinel-volte-cdma'
          addrinfo: '987654'
          is-prefix: false
          trtype: 0
          ssn: 146
Previous page Next page
Rhino VoLTE TAS VMs Version 4.1