This page contains some example partial RVT SDF service group definitions, that demonstrate how to configure various traffic schemes in the SDF.

Without SCTP multihoming

All signaling on one interface

The split traffic types were introduced in version 4.0.0-12-1.0.0. Prior to that version there were only signaling and signaling2 traffic types, which became deprecated in 4.0.0-12-1.0.0 and will be removed in a future version.

When upgrading from a prior version, you may want to keep the same networking topology to avoid reconfiguring VNFI networks, firewalls, and the like. As such, for this case you should use the traffic scheme where all signaling is on one interface.

The following example shows how to configure this for the SMO node, which uses all four of the signaling traffic types (internal, diameter, sip and ss7). For other node types you should only include the traffic types relevant to that node, as described in Traffic types and traffic schemes.

  networks:
    - ip-addresses:
        ip:
          - 172.16.0.11
      name: Management
      subnet: management
      traffic-types:
        - management
    - ip-addresses:
        ip:
          - 172.17.0.11
      name: Cluster
      subnet: cluster
      traffic-types:
        - cluster
    - ip-addresses:
        ip:
          - 172.18.0.11
      name: Signaling
      subnet: signaling
      traffic-types:
        - internal
        - diameter
        - sip
        - ss7

Signaling split across many interfaces

The following example shows the most fault-tolerant traffic scheme currently permitted, where the four traffic types are split amongst three interfaces.

  networks:
    - ip-addresses:
        ip:
          - 172.16.0.11
      name: Management
      subnet: management
      traffic-types:
        - management
    - ip-addresses:
        ip:
          - 172.17.0.11
      name: Cluster
      subnet: cluster
      traffic-types:
        - cluster
    - ip-addresses:
        ip:
          - 172.18.0.11
      name: Core Signaling
      subnet: core-signaling
      traffic-types:
        - internal
        - sip
    - ip-addresses:
        ip:
          - 172.19.0.11
      name: SS7 Signaling
      subnet: ss7-signaling
      traffic-types:
        - ss7
    - ip-addresses:
        ip:
          - 172.20.0.11
      name: Diameter Signaling
      subnet: diameter-signaling
      traffic-types:
        - diameter

With SCTP multihoming

Using Diameter multihoming on ShCM

The following example shows a basic Diameter multihoming setup for the ShCM node. (ShCM does not use the cluster traffic type, so it is not included here.)

  networks:
    - ip-addresses:
        ip:
          - 172.16.0.11
      name: Management
      subnet: management
      traffic-types:
        - management
    - ip-addresses:
        ip:
          - 172.17.0.11
      name: Core Signaling
      subnet: core-signaling
      traffic-types:
        - internal
        - diameter
    - ip-addresses:
        ip:
          - 172.18.0.11
      name: Diameter Multihoming
      subnet: diameter-secondary
      traffic-types:
        - diameter_multihoming

Using both SS7 and Diameter multihoming on SMO

Whether the selected traffic scheme has both the ss7 and diameter traffic types on the same subnet or on different subnets does not affect the options available for multihoming. The following example shows how to configure the secondary (multihoming) traffic types on separate interfaces despite using only one signaling interface for all the primary signaling traffic types.

  networks:
    - ip-addresses:
        ip:
          - 172.16.0.11
      name: Management
      subnet: management
      traffic-types:
        - management
    - ip-addresses:
        ip:
          - 172.17.0.11
      name: Cluster
      subnet: cluster
      traffic-types:
        - cluster
    - ip-addresses:
        ip:
          - 172.18.0.11
      name: Signaling
      subnet: signaling
      traffic-types:
        - internal
        - diameter
        - sip
        - ss7
    - ip-addresses:
        ip:
          - 172.19.0.11
      name: Diameter Multihoming
      subnet: diameter-secondary
      traffic-types:
        - diameter_multihoming
    - ip-addresses:
        ip:
          - 172.20.0.11
      name: SS7 Multihoming
      subnet: ss7-secondary
      traffic-types:
        - ss7_multihoming
Previous page Next page
Rhino VoLTE TAS VMs Version 4.2