Planning for the procedure

Background knowledge

This procedure assumes that:

  • you are installing into an existing OpenStack deployment

    • The OpenStack deployment must be set up with support for Heat templates.

  • you are using an OpenStack version from Icehouse through to Train inclusive

  • you are thoroughly familiar with working with OpenStack machines and know how to set up tenants, users, roles, client environment scripts, and so on.
    (For more information, refer to the appropriate OpenStack installation guide for the version that you are using here.)

  • you are upgrading an existing downlevel deployment for MMT CDMA.

  • you have deployed a SIMPL VM, and have followed all the pre-upgrade steps.

Reserve maintenance period

This procedure requires a maintenance period. When integrating into a live network, we recommend that you implement measures to mitigate any unforeseen events.

Plan for service impact

Misconfiguration could disrupt services for existing network elements.

People

You must be a system operator to perform the MOP steps.

Tools and access

You must have access to the SIMPL VM, and the SIMPL VM must have the right permissions on the OpenStack deployment.

Method of procedure

Note Refer to the SIMPL VM Documentation for details on the commands mentioned in the procedure.

Step 1 - Check OpenStack quotas

The SIMPL VM creates one server group per VM, and one security group per interface on each VM. OpenStack sets limits on the number of server groups and security groups through quotas.

View the quota by running openstack quota show <project id> on OpenStack Controller node. This shows the maximum number of various resources.

You can view the existing server groups by running openstack server group list. Similarly, you can find the security groups by running openstack security group list

If the quota is too small to accommodate the new VMs that will be deployed, increase it by running
openstack quota set --<quota field to increase> <new quota value> <project ID>. For example:
openstack quota set --server-groups 100 125610b8bf424e61ad2aa5be27ad73bb

See CSAR EFIX patches to learn more on the CSAR EFIX patching process.

Step 2 - Upgrade the downlevel MMT CDMA VMs

The VM with the Rhino node that has the lowest ID must be upgraded last.

Upgrade all of the other VMs using the following command: csar update --vnf mmt-cdma --sites <site> --service-group <service_group> --index-range <range> --sdf <path to SDF>.

The indexes start from 0, therefore 0 is the first VM. The --index-range accepts ranges as well as comma separated indexes (e.g. 1-3,7,9). To upgrade the VMs in stages, run the command multiple times using the appropriate --index-range values.

The following will occur one MMT CDMA node at a time:

  • The downlevel node will be quiesced.

  • The uplevel node will be created and boot up.

  • The VM will automatically start applying configuration from the files you uploaded to CDS in the above steps. During this phase, the status of the VM in MDM will be Orange.

  • Once configuration is complete, the status will change to Green, and the node will be ready for service. At this point the csar update command will move on to the next MMT CDMA VM, or report that the upgrade of the MMT CDMA was successful if all nodes have now been upgraded.

  • Once the upgrade is complete, place calls and run any additional validation tests to verify the uplevel VMs are working as expected.

Step 3 - Upgrade the final MMT CDMA VM

Upgrade the VM with the Rhino node that has the lowest ID.

Run the following command: csar update --vnf mmt-cdma --sites <site> --service-group <service_group> --index-range <index> --sdf <path to SDF>.

Backout procedure

If the upgrade has brought up uplevel VMs to replace the downlevel VMs, then the uplevel VMs can be rolled back to the downlevel VMs. To rollback, repeat the steps above with the downlevel MMT CDMA CSAR and downlevel SDF. The lowest uplevel VM must be rolled back last. For example, if VMs 2-5 are in the uplevel, you must rollback VMs 3-5 then rollback VM 2.

You may need to use the --skip pre-update-checks flag as part of the csar update command. The --skip pre-update-checks flag allows rollbacks when a node is unhealthy.

If the upgrade has failed to bring up the uplevel VMs or the rollback has failed to bring up the downlevel VMs, then you must redeploy the downlevel VMs. run csar redeploy --vnf mmt-cdma --sites <site> --sdf <path to SDF>.

Diagnostics during the quiesce stage

When the downlevel VMs are quiesced, they upload some diagnostics to the CDS. These may be useful if the upgrade or rollback fails.

To get these diagnostics, follow instructions from Retrieving Initconf and Rhino logs with export-log-history.

Next Step

If you are upgrading a full set of VMs, go to Rolling CSAR EFIX patch SMO nodes on OpenStack, otherwise follow the post upgrade instructions here: Post rolling upgrade using CSAR EFIX patch steps

Previous page Next page
Rhino VoLTE TAS VMs Version 4.0.0