This section applies in the case where the Rhino VoLTE TAS SGC has previously received its initial configuration and now requires reconfiguration.

Reconfiguration of the SGC requires a SMO or an SGC VM with version 4.0.0-9-1.0.0 or newer. Reconfiguration of the SGC component in older VMs is not supported.

Warning

Reconfiguring the SGC will cause a full SS7 outage in live deployments.
Warning

You must carry out the process documented here exactly as documented. It should not be skipped or modified.

What you need

  • ❏ The sgctool utility (available on the SGC or SMO VM).

  • ❏ The IP address of one of the deployment’s TSN nodes (<cds_address>).

  • ❏ The deployment ID (<deployment_id>).

  • ❏ The group ID (<group_id>).

Process overview

Here is the high-level view of the required steps:

  1. Review the configuration.

  2. Stop the OCSS7 SGCs.

  3. Verify that the OCSS7 SGCs are stopped.

  4. Delete the OCSS7 SGCs.

  5. Clear OCSS7 SGC-related state from the TSN nodes (CDS).

  6. Apply the new configuration.

Process detail

1. Review the configuration

Warning

Do not skip this step. Applying the configuration without reviewing it may result in loss of service.

Previous releases of the Rhino VoLTE TAS VM contained defects that resulted in the configuration being incorrectly applied. These defects have since been corrected. The reconfiguration process removes all previous configuration, including the incorrectly applied configuration, and replaces it with correctly applied configuration. This may result in changes in behavior, which in some cases could result in loss of service if the configuration was affected by this defect and is not adjusted appropriately.

See reviewing the SGC configuration for full details.

2. Stop the OCSS7 SGCs

You need to stop every SGC in the cluster. On each SGC or SMO node, issue the following command:

$ sudo systemctl stop ocss7

Note

The following message may be safely ignored:

Warning: ocss7.service changed on disk. Run 'systemctl daemon-reload' to reload units.

3. Verify that the OCSS7 SGCs are stopped

  1. Check the systemctl status of the ocss7 service. On each SGC or SMO node issue the following command:

$ sudo systemctl status ocss7
Dec 22 15:45:28 tst-sgc-1 systemd[1]: Stopping Start the OCSS7 SGC...
Dec 22 15:45:28 tst-sgc-1 ocss7[5029]: Stopping processes:
Dec 22 15:45:28 tst-sgc-1 ocss7[5029]: SGC:2027
Dec 22 15:45:28 tst-sgc-1 ocss7[5029]: DAEMON:2017
Dec 22 15:45:28 tst-sgc-1 ocss7[5029]: Initiating graceful shutdown for [2027] ...
Dec 22 15:45:28 tst-sgc-1 ocss7[5029]: Sleeping for max 32 sec waiting for graceful shutdown to complete.
Dec 22 15:45:39 tst-sgc-1 ocss7[5029]: Graceful shutdown successful
Dec 22 15:45:39 tst-sgc-1 ocss7[5029]: Shutdown complete (graceful)
Dec 22 15:45:39 tst-sgc-1 systemd[1]: Stopped Start the OCSS7 SGC.

  1. Check the OCSS7 SGC’s view of its own status. On each SGC or SMO node issue the following command:

$ ~/ocss7/<deployment_id>/<instance_id>/current/bin/sgc status
SGC is down

4. Delete the OCSS7 SGCs

On each SGC or SMO node, remove the OCSS7 SGC installation:

$ rm -rf /home/sentinel/ocss7/<deployment_id>/
Warning

Do not delete /home/sentinel/ocss7/, as this contains the necessary packages to reinstall the OCSS7 SGC.

Remove OCSS7 SGC configuration data that was persisted to the Cassandra Data Store (CDS). This only needs to be carried out once per SGC or SMO cluster.

  1. Run the sgctool from one SGC or SMO VM:

$ /opt/tasvmruntime-py/bin/sgctool clear-config --cds-address <cds_address> --deployment-id <deployment_id> --group-id <group_id>
The CDS SGC state has been cleared
Note

The <group_id> syntax is: RVT-<node type>[-suffix].<site_id>. For example: RVT-smo.DC1.

6. Apply the new configuration

You may now apply the new configuration using rvtconfig, as documented in Declarative configuration.

Previous page Next page
Rhino VoLTE TAS Version 4.2