Planning for the procedure

Background knowledge

This procedure assumes that:

  • you are installing into an existing VMware vSphere deployment which has pre-configured networks and VLANs; this procedure does not cover setting up a VMware vSphere deployment from scratch

  • you are upgrading an existing downlevel deployment for SMO.

  • you have deployed a SIMPL VM, and have followed all the pre-upgrade steps.

Reserve maintenance period

This procedure does require a maintenance period. When integrating into a live network, it is recommended to implement measures to mitigate any unforeseen events.

Plan for service impact

Misconfiguration could disrupt service for existing network elements.

People

You must be a system operator to perform the MOP steps.

Tools and access

You must have access to the SIMPL VM, and the SIMPL VM must have the right permissions on the VMware vSphere deployment.

Method of procedure

Note Refer to the SIMPL VM Documentation for details on the commands mentioned in the procedure.

See CSAR EFIX patches to learn more on the CSAR EFIX patching process.

Deployments using SIMPL 6.7.3

Step 1 - Upgrade the downlevel SMO VMs

The VM with the Rhino node that has the lowest ID must be upgraded last.

So update all of the other VMs using: csar update --vnf smo --sites <site> --service-group <service_group> --index-range <range> --sdf <path to SDF>.

The indexes start from 0, therefore 0 is the first VM. The range accepts ranges as well as comma separated indexes (e.g. 1-3,7,9).

The following will occur one SMO node at a time:

  • The downlevel node will be quiesced.

  • The uplevel node will be created and boot up.

  • The VM will automatically start applying configuration from the files you uploaded to CDS in the above steps. During this phase, the status of the VM in MDM will be Orange.

  • Once configuration is complete, the status will change to Green, and the node will be ready for service. At this point the csar update command will move on to the next SMO VM, or report that the upgrade of the SMO was successful if all nodes have now been upgraded.

Step 2 - Upgrade the final SMO VM

Ugrade the VM with the Rhino node that has the lowest ID

Run the following command: csar update --vnf smo --sites <site> --service-group <service_group> --index-range <index> --sdf <path to SDF>.

Backout procedure

If the upgrade has brought up uplevel VMs to replace the downlevel VMs, then the uplevel VMs can be rolled back to the downlevel VMs. To rollback, repeat the steps above with the downlevel SMO CSAR and downlevel SDF. The lowest uplevel VM must be rolled back last. For example, if VMs 2-5 are in the uplevel, you must rollback VMs 3-5 then rollback VM 2.

You may need to use the --skip pre-update-checks flag as part of the csar update command. The --skip pre-update-checks flag allows rollbacks when a node is unhealthy.

If the upgrade has failed to bring up the uplevel VMs or the rollback has failed to bring up the downlevel VMs, then you must redeploy the downlevel VMs. run csar redeploy --vnf smo --sites <site> --sdf <path to SDF>.

Diagnostics during the quiesce stage

When the downlevel VMs are quiesced, they upload some diagnostics to CDS. These may be useful if the upgrade or rollback fails.

To get these diagnostics, follow instructions from Retrieving Initconf, Rhino and SGC logs with export-log-history.

Deployments using SIMPL 6.6.x

Step 1 - Validate the SDF

Run csar validate-vsphere --sdf <path to SDF>.

This will validate the uplevel SDF.

Step 2 - Generate the Terraform Template

Run csar generate --vnf smo --sdf <path to SDF>.

This will generate the terraform template.

Step 3 - Upgrade the downlevel SMO VMs

The VM with the Rhino node that has the lowest ID must be upgraded last.

So update all of the other VMs using: csar update --vnf smo --sites <site> --service-group <service_group> --index-range <range>.

The indexes start from 0, therefore 0 is the first VM. The range accepts ranges as well as comma separated indexes (e.g. 1-3,7,9).

The following will occur one SMO node at a time:

  • The downlevel node will be quiesced.

  • The uplevel node will be created and boot up.

  • The VM will automatically start applying configuration from the files you uploaded to CDS in the above steps. During this phase, the status of the VM in MDM will be Orange.

  • Once configuration is complete, the status will change to Green, and the node will be ready for service. At this point the csar update command will move on to the next SMO VM, or report that the upgrade of the SMO was successful if all nodes have now been upgraded.

Step 4 - Upgrade the final SMO VM

Ugrade the VM with the Rhino node that has the lowest ID

Run the following command: csar update --vnf smo --sites <site> --service-group <service_group> --index-range <index>.

Backout procedure

If the upgrade has brought up uplevel VMs to replace the downlevel VMs, then the uplevel VMs can be rolled back to the downlevel VMs. To rollback, repeat the steps above with the downlevel SMO CSAR and downlevel SDF. The lowest uplevel VM must be rolled back last. For example, if VMs 2-5 are in the uplevel, you must rollback VMs 3-5 then rollback VM 2.

You may need to use the --skip-pre-update-checks flag as part of the csar update command. The --skip-pre-update-checks flag allows rollbacks when a node is unhealthy.

If the upgrade has failed to bring up the uplevel VMs or the rollback has failed to bring up the downlevel VMs, then you must redeploy the downlevel VMs. run csar deploy --redeploy --vnf smo --sites <site>.

Diagnostics during the quiesce stage

When the downlevel VMs are quiesced, they upload some diagnostics to CDS. These may be useful if the upgrade or rollback fails.

To get these diagnostics, follow instructions from Retrieving Initconf, Rhino and SGC logs with export-log-history.

Next Step

Follow the post upgrade instructions here: Post rolling upgrade using CSAR EFIX patch steps

Previous page Next page
Rhino VoLTE TAS VMs Version 4.0.0