SIP Session Replication

When replication is enabled, the SIS initially creates the dialog state in local memory. When the dialog reaches the "Confirmed" state, the SIS writes the dialog state to its replicated store. This is either Rhino’s in-memory database, or an external key-value store, such as Cassandra.

When the creating node receives mid-dialog requests, it processes the requests normally using the dialog state in local memory. When the SIP transaction completes, the updated dialog state is written to the replicated store.

When a dialog-terminating request such as BYE is processed, the local and replicated dialog state is removed when the transaction completes.

If a node fails, it is assumed that an external mechanism, such as DNS or a load balancer, will direct SIP traffic to the surviving nodes in a cluster.

When a node receives a mid-dialog request for a dialog that does not exist in local memory, it attempts to load the dialog from its replicated state.

When the original node recovers, failed-over dialogs do not migrate back to that node. Rather, the dialog remains on the node that last took over ownership of the dialog, as long as that node is alive. This is managed by Session Ownership.

The SIS uses Rhino’s Session Ownership facility to track which node is currently responsible for a dialog. This is to ensure that requests in a dialog are processed on the same node if possible, for consistency. Otherwise dialog state could be updated by several nodes, leading to errors. In other words, dialogs are "sticky" and will only migrate to another node in the event of a node failure.

When a SIS node receives a mid-dialog request for a dialog that it does not currently own, the request is automatically proxied to the owning node, as determined by the Session Ownership facility. If the owning node is down, then the current node may take over ownership of the dialog and resume processing the request. The Session Ownership facility ensures that subsequent requests for this dialog will be directed to the correct node.

The replication method is determined by the Rhino namespace that the SIS instance is deployed into.

Rhino 2.6.1 supports two replication methods:

The key-value-store method is preferred for large clusters.

Rhino’s Session Ownership facility is automatically available to the SIS instance if its namespace has session ownership enabled. This requires configuring a Session Ownership store in Rhino, and creating a namespace with session ownership support.

The sessionReplicationMode configuration property on the SIS-SIP EasySIP RA determines whether session replication will be used. This property has three values:

The default value is automatic.

When replication is enabled in the SIS, there is also the option to selectively enable it on particular sessions. This is controlled by the replicateByDefault boolean configuration property:

The default value is true.

When startReplicating() is called, the SIS replicates the session as soon as it is able to. If the dialog is not yet confirmed, replication will begin when it reaches the confirmed state. If the dialog is already confirmed, replication begins immediately, storing the current dialog state.

To make use of per-node SRV addresses, the DynamicSRVNameFormat network interface property must be configured.

The value of this property is a string that describes how a DNS SRV name is derived from the node’s IP address. The special token ${IP} is replaced with a DNS-safe encoding of the node’s IP address, that may be used as a domain name component.

For example if DynamicSRVNameFormat is tas-${IP}.site1.home1.net, then the node with IP address 192.168.10.1 will use the hostname tas-192-168-10-1.site1.home1.net in its Contact or Record-Route URIs.

For IPv6 addresses, each 2-octet group is hex-encoded and delimited with a hyphen. For example the address 1080::8:800:200C:417A is encoded as 1080-0000-0000-0000-0008-0800-200c-417a.

Say we have three SIS nodes, hostnames sis-1.home1.net, sis-2.home1.net and sis-3.home1.net. Their address records in DNS are:

By configuring the DynamicSRVNameFormat network interface property with value ip-${IP}.home1.net, the SIS nodes will use URIs of the form sip:ip-192-168-10-1;lr;transport=tcp.

The operator provisions the corresponding DNS SRV records:

For each per-node SRV address, there are 3 records. The first points to the node’s own host name, and the other records point to the 2 other node’s host names. The addresses are always tried in priority order (lowest to highest), by the rules of RFC 3263 and RFC 2782.

If node sis-1 fails, mid-dialog requests routed to sip:ip-192-168-10-1.home1.net will go to sis-2 if available, otherwise sis-3. This ensures that dialogs are "sticky" to the node that created them. Mid-dialog requests are automatically routed to the same node, but if that node fails, it is clear which node will be tried next.

Initial requests can be directed to a virtual address, DNS NAPTR or SRV address that distributes traffic over all nodes in the cluster. So for the example cluster above, using a DNS SRV address we can say that all nodes have equal priority and weight:

When a SIP client sends an initial request to the URI sip:sis.home1.net;transport=tcp, it will automatically select one of the three nodes at random as the destination for that request.

SipMessage objects may now be easily encoded to byte streams and back. This makes it easy to store messages in SBB CMP fields, for example. See SipFactory.encodeMessage() and SipFactory.decodeMessage().

The method SipSession.startReplicating() requests that the session be replicated if possible. It is only meaningful if the replicateByDefault boolean configuration property is false.

The method may be called at any point in the session’s lifetime. The session will not actually be replicated until it reaches the "Confirmed" state. If the session is already in the "Confirmed" state when the method is invoked, replication begins immediately. Multiple invocations of this method have no effect.

The SipSession.getDialogID() method gets the session’s DialogID, consisting of Call-ID, local and remote tags.

The string form of this dialog ID may be used as the tracking key in the Session Ownership facility.

Each SIS instance has its own unique URI, referred to as the internal application server URI (AS URI). This is a SIP URI used by the SIS for its own communication between SIS nodes. Currently this is used when Session Ownership determines that a mid-dialog request must be handled by another node.

Applications must use the the internal AS URI as the "owner URI" for a session ownership record. The SipFactory methods SipFactory.getInternalASURI() and SipFactory.isInternalASURI() are used to obtain and check these URIs.